Robotics Lab

Robotics Lab: Explore Boards in 3D

Explore eight boards from Arduino, Espressif and Raspberry Pi. Inspect their components in 3D, assemble a board or wire a working circuit.

Building the board…

01Workbench

Robotics Lab circuit workbench

Wire sensors, motors and displays to a board, then press Run to simulate the circuit. Start with a guided mission or build your own circuit in Free Build.

  • Guided circuit missions

    Step-by-step builds — blink an LED, read a sensor, drive a motor.

  • Pin-to-pin wiring

    Click a pin, click another: the bench checks every connection before power-up.

  • Full-screen workbench

    Press Full screen in the workbench toolbar to give the bench the whole display.

02Lesson

Robotics Lab: NodeMCU (ESP8266) Lesson and Pinout

Select a board in Robotics Lab to see its specifications, pin functions and component guide.

In short

NodeMCU / Amica · 2015

A tiny Wi-Fi board built around the ESP8266 chip: it plugs into a breadboard, is programmed over USB from the Arduino IDE and gets online all by itself. It is the classic starting point for smart-home gadgets, phone-controlled robots and sensors that send their readings to the internet.

Clock
80 MHz
Flash
4 MB
RAM
≈80 KB
GPIO pins
11
Logic level
3.3 V
Price
≈ $3

Specs

The full data sheet in plain words.

Microcontroller
ESP8266EX (ESP-12E module)
Core
Tensilica L106, 32-bit, single core
Clock speed
80 MHz (up to 160 MHz)
Flash memory
4 MB (separate chip inside the module)
RAM
≈80 KB, about 50 KB free for your program
Wireless
Wi-Fi 802.11 b/g/n, 2.4 GHz; no Bluetooth
Logic level
3.3 V (inputs are not 5 V tolerant)
Digital pins
11 (D0–D8, RX, TX), PWM on D1–D8
Analog inputs
1 (A0, 0–3.3 V, 10-bit)
Interfaces
UART, I²C, SPI
USB
Micro-USB, CP2102 bridge
Power
USB 5 V or Vin 5–10 V; AMS1117-3.3 regulator
Size
48 × 26 mm

What’s on the board

14 parts, numbered like the labels on the 3D model. Click one and the camera flies to it.

Strengths and pitfalls

Why people love this board — and where beginners usually slip.

Strengths

  • Wi-Fi right on the board: web server, MQTT, control from a phone — no extra modules needed
  • Programmed from the Arduino IDE (or in MicroPython) — familiar sketches and libraries just work
  • One-click upload over USB: the auto-reset circuit puts the chip into bootloader mode for you
  • Fast 32-bit processor and 4 MB of flash — many times more than an Arduino Uno

Watch out

  • 3.3 V logic: a 5 V signal from an Arduino or a sensor (e.g. the Echo pin of an HC-SR04) can destroy an input — use a voltage divider or a level shifter
  • There is only one analog input, and A0 must never see more than 3.3 V
  • D3, D4 and D8 are strapping pins: if a sensor or button holds them at the wrong level at power-up, the board will not start
  • A pin can supply only about 12 mA: power motors, servos and relays from a separate supply and connect the grounds together
  • Pins SD0–SD3, CMD and CLK belong to the flash memory — leave them alone

Pins

The contacts where sensors, motors and power connect.

Power

Power the board from USB or feed 5 V into Vin. 3V3 is the regulator output for sensors (a couple of hundred mA in total, shared with the chip itself, which draws bursts of up to 300 mA while transmitting). All GND pins are connected together.

D numbers vs GPIO

The board says D0–D8 but programs often use GPIO numbers: D0=16, D1=5, D2=4, D3=0, D4=2, D5=14, D6=12, D7=13, D8=15. In the Arduino IDE you can simply write D1, D2 — the constants are already defined.

Safe pins

Feel free to use D1, D2, D5, D6 and D7 — they have no special roles. D3, D4 and D8 affect how the chip boots, D0 has no PWM or interrupts, and RX/TX are busy talking to the computer.

Analog input

A0 is the only one on the board: 0–3.3 V, values from 0 to 1023. If you need several analog sensors, add an external I²C ADC (such as the ADS1115) or a multiplexer.

Buses

I²C: D1 (SCL) and D2 (SDA) — displays, gyroscopes, sensors. SPI: D5 (SCK), D6 (MISO), D7 (MOSI), D8 (CS). PWM for motors and LEDs works on D1–D8, 10-bit by default (0…1023).

Hover over any pin on the 3D board to see its name and function.

  • Power
  • Ground
  • Digital
  • Analog
  • Buses: UART, I²C, SPI
  • Control: RESET, EN, BOOT
  • Not connected

First code

Copy it, upload it to the board and check that everything works.

First sketch: blink and join Wi-Fi Arduino C++
#include <ESP8266WiFi.h>const char* ssid = "MyWiFi";        // your network nameconst char* pass = "12345678";      // its passwordvoid setup() {  pinMode(LED_BUILTIN, OUTPUT);     // blue LED on D4 (GPIO2)  Serial.begin(115200);  WiFi.begin(ssid, pass);           // start connecting  while (WiFi.status() != WL_CONNECTED) {    // no network yet — blink fast    digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));    delay(200);  }  Serial.print("My IP address: ");  Serial.println(WiFi.localIP());}void loop() {  digitalWrite(LED_BUILTIN, LOW);   // LOW turns the LED ON (it is inverted)  delay(100);  digitalWrite(LED_BUILTIN, HIGH);  // HIGH turns it off  delay(1900);                      // one short flash every 2 seconds}

Where it shines

Project ideas this board suits best.

  1. Wi-Fi rover: drive the motors from your phone through a web page
  2. Weather station: temperature and humidity sensor posting to a website or a chat bot
  3. Smart plug or light: a relay switched over Wi-Fi and on a schedule
  4. Robot remote and telemetry: sensor readings shown live on a phone screen
  5. Teamed with an Arduino: NodeMCU handles the network, the second board drives the motors

Facts

The ESP8266 appeared in 2014 as a cheap "Wi-Fi adapter" for other microcontrollers — only later did hobbyists discover that it makes a great main processor on its own.

The name NodeMCU comes from a firmware based on the Lua language; today these boards are mostly programmed from the Arduino IDE or in MicroPython.

In deep sleep the ESP8266 chip itself draws only about 20 µA, so a bare module can run a battery-powered sensor for months. On this dev board the USB bridge and the regulator add a few milliamps on top.

03Quiz & assembly

Robotics Lab: Component Quiz and Soldering

Use the 3D models in Robotics Lab to identify components, place them on the board and practice soldering. Both exercises work with all eight boards.

Quiz · about a minute

Identify components on a 3D board

We name a part — you find it on the model and click it. Rotate the board, zoom in and flip it over, just like the real thing.

  1. 1

    Read the question. “Find the microcontroller — the brain of the board.”

  2. 2

    Click the part. Not sure? Take a hint, or skip and see the answer.

  3. 3

    See your score. Only first-try answers without a hint count.

Assembly · a few minutes

Assemble and solder a board

The board comes apart into a tray of parts on the bench. Put every chip, connector and header back where it belongs and solder it down.

  1. 1

    Pick a part from the tray. Chips, connectors, headers, buttons.

  2. 2

    Place it on its footprint. The pads on the bare board show where it goes.

  3. 3

    Solder it in. When the last joint is done, the board is whole again.

04Compare

Robotics Lab: Compare All Eight Boards

Compare processors, memory, pins and logic voltage to choose a board for your project. Select a row to open that board in Robotics Lab.

Prices are typical street prices and vary by seller. “Logic” is the voltage of the I/O pins — never feed 5 V into a 3.3 V board.

Robotics Lab FAQ

What can I do in Robotics Lab?

Rotate eight 3D circuit boards, inspect their pins and components, practice assembling and soldering a board, and wire virtual circuits in the browser.

Which boards can I explore?

The lab includes the Arduino Uno R3, Arduino Nano, Arduino Mega 2560 R3, ESP32 DevKit V1, NodeMCU, Raspberry Pi Pico, STM32 Blue Pill and Raspberry Pi 4 Model B.

Do I need a physical board or an account?

The virtual lab runs without an account or physical hardware. The 3D viewer and simulator need JavaScript and WebGL 2. Board specifications and lessons are readable without starting the viewer.

How do I get started with circuit simulation?

Open the circuit workbench and choose the first LED mission. Follow its wiring steps, press Run and watch the LED blink. Free Build lets you choose and connect your own components.

How does the component quiz score answers?

A correct first answer without a hint earns one point. A correct answer after a retry or hint still lets you complete the question. Your best score is saved in this browser.

Can I use the simulated wiring on real hardware?

Use the simulator to practice and understand the connections. Before wiring a physical board, check the manufacturer’s documentation for its pinout, voltage limits and power requirements.