Robotics Lab

Robotics Lab: Explore Boards in 3D

Explore eight boards from Arduino, Espressif and Raspberry Pi. Inspect their components in 3D, assemble a board or wire a working circuit.

Building the board…

01Workbench

Robotics Lab circuit workbench

Wire sensors, motors and displays to a board, then press Run to simulate the circuit. Start with a guided mission or build your own circuit in Free Build.

  • Guided circuit missions

    Step-by-step builds — blink an LED, read a sensor, drive a motor.

  • Pin-to-pin wiring

    Click a pin, click another: the bench checks every connection before power-up.

  • Full-screen workbench

    Press Full screen in the workbench toolbar to give the bench the whole display.

02Lesson

Robotics Lab: Arduino Uno R3 Lesson and Pinout

Select a board in Robotics Lab to see its specifications, pin functions and component guide.

In short

Arduino · 2010

The best-known learning board in the world. A simple, tough 8-bit ATmega328P microcontroller, forgiving 5 V logic and sockets that take jumper wires without soldering. Thousands of tutorials are written for it, and hundreds of add-on boards — "shields" — plug straight on top.

Clock
16 MHz
Flash
32 KB
RAM
2 KB
GPIO pins
14 + 6
Logic level
5 V
Price
≈ $25

Specs

The full data sheet in plain words.

Microcontroller
ATmega328P (8-bit AVR)
Clock speed
16 MHz
Flash memory
32 KB (0.5 KB used by the bootloader)
RAM / EEPROM
2 KB / 1 KB
Digital pins
14, of which 6 with PWM
Analog inputs
6 (10-bit ADC)
Logic voltage
5 V
Power
USB 5 V, or 7–12 V via the jack / Vin
Current per pin
20 mA (absolute maximum 40 mA)
Interfaces
UART, I²C, SPI
Computer link
USB-B through an ATmega16U2 bridge
Size
68.6 × 53.4 mm, 25 g

What’s on the board

15 parts, numbered like the labels on the 3D model. Click one and the camera flies to it.

Strengths and pitfalls

Why people love this board — and where beginners usually slip.

Strengths

  • Forgiving: 5 V logic and sturdy pins survive a lot of beginner mistakes
  • Huge community — every question already has an answer and a ready example
  • Hundreds of shields: motor drivers, relays and displays stack on top with no wiring
  • The microcontroller sits in a socket — a burnt chip can simply be swapped

Watch out

  • No more than 20 mA from one pin: LEDs always need a resistor; motors and relays only through a driver or a transistor
  • Do not power servos and motors from the board's 5V pin — give them their own supply and join the grounds (GND)
  • 3.3 V sensors and modules must not be wired straight to the 5 V signal pins — use a level shifter
  • Pins 0 and 1 are shared with the USB link: while something is connected to them a sketch may fail to upload

Pins

The contacts where sensors, motors and power connect.

Power

5V and 3.3V are outputs for sensors and modules; GND is the common ground that every device in the circuit shares. Vin is the 7–12 V input. The 3.3V pin can supply no more than 50 mA.

Digital pins and PWM

Pins 0–13 work as inputs and outputs with 0 V and 5 V levels. The "~" next to 3, 5, 6, 9, 10 and 11 means PWM: analogWrite() smoothly controls brightness and speed.

Analog inputs

A0–A5 read a 0–5 V voltage with analogRead() and return a number from 0 to 1023. If you run out of digital pins, they also work as ordinary digital pins (D14–D19).

Buses

UART — pins 0 (RX) and 1 (TX), shared with the USB link to the computer. I²C — SDA and SCL (the same lines as A4 and A5). SPI — pins 10–13 and the ICSP header.

Interrupts

Pins 2 and 3 can react to a signal instantly, even when the program is busy with something else — attachInterrupt(). Handy for wheel encoders on a robot.

Hover over any pin on the 3D board to see its name and function.

  • Power
  • Ground
  • Digital
  • Analog
  • Buses: UART, I²C, SPI
  • Control: RESET, EN, BOOT
  • Not connected

First code

Copy it, upload it to the board and check that everything works.

First sketch: blink the built-in LED Arduino C++
// LED "L" is already on the board and wired to pin 13.// LED_BUILTIN is the ready-made name for that pin.void setup() {  pinMode(LED_BUILTIN, OUTPUT);     // pin 13 works as an output  Serial.begin(9600);               // open the USB link to the computer}void loop() {  digitalWrite(LED_BUILTIN, HIGH);  // 5 V on the pin — the LED is on  Serial.println("on");             // shows up in the Serial Monitor  delay(500);                       // wait half a second  digitalWrite(LED_BUILTIN, LOW);   // 0 V — the LED is off  Serial.println("off");  delay(500);}

Where it shines

Project ideas this board suits best.

  1. A first two-motor robot with a motor-driver shield
  2. An obstacle-avoiding robot with an ultrasonic distance sensor
  3. A line-following robot
  4. A robot arm on hobby servos
  5. A weather station with a display and sensors

Facts

"Uno" is Italian for "one": the board was named to mark the release of the Arduino 1.0 software.

Arduino was created in the Italian town of Ivrea and named after the bar where its founders used to meet. The bar, in turn, is named after Arduin of Ivrea, a king who ruled about a thousand years ago.

The board's design files are open to everyone — which is why there are so many compatible boards and clones.

03Quiz & assembly

Robotics Lab: Component Quiz and Soldering

Use the 3D models in Robotics Lab to identify components, place them on the board and practice soldering. Both exercises work with all eight boards.

Quiz · about a minute

Identify components on a 3D board

We name a part — you find it on the model and click it. Rotate the board, zoom in and flip it over, just like the real thing.

  1. 1

    Read the question. “Find the microcontroller — the brain of the board.”

  2. 2

    Click the part. Not sure? Take a hint, or skip and see the answer.

  3. 3

    See your score. Only first-try answers without a hint count.

Assembly · a few minutes

Assemble and solder a board

The board comes apart into a tray of parts on the bench. Put every chip, connector and header back where it belongs and solder it down.

  1. 1

    Pick a part from the tray. Chips, connectors, headers, buttons.

  2. 2

    Place it on its footprint. The pads on the bare board show where it goes.

  3. 3

    Solder it in. When the last joint is done, the board is whole again.

04Compare

Robotics Lab: Compare All Eight Boards

Compare processors, memory, pins and logic voltage to choose a board for your project. Select a row to open that board in Robotics Lab.

Prices are typical street prices and vary by seller. “Logic” is the voltage of the I/O pins — never feed 5 V into a 3.3 V board.

Robotics Lab FAQ

What can I do in Robotics Lab?

Rotate eight 3D circuit boards, inspect their pins and components, practice assembling and soldering a board, and wire virtual circuits in the browser.

Which boards can I explore?

The lab includes the Arduino Uno R3, Arduino Nano, Arduino Mega 2560 R3, ESP32 DevKit V1, NodeMCU, Raspberry Pi Pico, STM32 Blue Pill and Raspberry Pi 4 Model B.

Do I need a physical board or an account?

The virtual lab runs without an account or physical hardware. The 3D viewer and simulator need JavaScript and WebGL 2. Board specifications and lessons are readable without starting the viewer.

How do I get started with circuit simulation?

Open the circuit workbench and choose the first LED mission. Follow its wiring steps, press Run and watch the LED blink. Free Build lets you choose and connect your own components.

How does the component quiz score answers?

A correct first answer without a hint earns one point. A correct answer after a retry or hint still lets you complete the question. Your best score is saved in this browser.

Can I use the simulated wiring on real hardware?

Use the simulator to practice and understand the connections. Before wiring a physical board, check the manufacturer’s documentation for its pinout, voltage limits and power requirements.